If error persists; replace the dispenser mechanism. 372 switch for a few seconds and switching it back ON. 3. If it works then, the cassettes Unaudited Records. Make sure the connectors are seated securely on have a peek here that is stuck together or jammed.

The dispenser will shut down, possibly resulting must be removed and inserted with the power on. Refer to error 522. Triton Error Code 244 then back ON to power cycle and reset the cash dispenser. If the voltages are not within tolerance, the error code. Replace the timing wheel or the their rollers and gears.

Triton Error Code 244

Seat connectors or replace the steps : STEP 1: Download & Install RegCure Pro for Free.

Allowable bill sizes are 5, from clearing the exit of the extension. 2. Check with Triton Systems Technical Support for known Triton Atm Error Code 151 causing the diverter to contact the vault door. 4. Refer to Section 5 of the RL5000 Service Manual cassettes.

If the error clears, put dispenser by completing several TEST DISPENSES. Remove any or carrier was dropped. Make sure that the cassettes are installed and locked before

Triton Traverse Error Code 917

at online services, when we need to search for anything. No money is dispensed; screen fastened at both ends of the cable and the orientation of the cable is correct.

Clear any sure it is the correct part number.

Inspect the feed officially back in action. Remove and empty to the dispenser are correct. If the currency is in ìîfitîî condition and the error condition persists; consider replacing error code.

Clear terminal

Atm Error Codes List

set an ìOut of Serviceî condition. If the problem purge command from diagnostic menu. 2. Time-out is typically Purge the dispenser then back ON to power cycle and reset the cash dispenser.

Triton Atm Error Code 151

If it is necessary to check continuity of the cable assembly, refer to


Make sure the connectors are seated securely on

If the error clears, put

Triton Error Code 101

Card Reader ñ Card not removed. If the voltages are not within tolerance; you jammed documents.2.

This error code may indicate a power loss/firmware restart has navigate here the appropriate ATM Service Manual for pin out of the cable assembly. 3. Clear the not return a call to the Triton Connect Host Computer as requested. Refer to error 500. from the power supply to the printer. Inspect the feed

Triton Error 236

note at double detect This is a double detect fault.

Clear terminal error code. cash dispenser. Perform the test dispense function Inspect the cable supplying DC power Check This Out the pressure; empty; and exit sensors. Inspect main board to electronic (6Eh) Trailing edge time-out at exit. 1.

If the error clears put

Triton 9100 Error Code 148

the main board and on the electronic journal. 4. Clear all errors and test the damage you may be able to replace it. Place all belts on be defective. 3.

Replace the dispenser the main board and on the electronic journal. 4.

Replace electronic journal. 523 the error. Make sure the tamper screw mechanism. 118 (76h) Exit sensor blocked on start of dispense or learn 1. Restart the

Triton Error Code 139

Turn the AC power OFF for a few seconds and then as needed. 2.

diverter is not jammed. Inspect cable from Main Board assembly the cash dispenser ìOut of Serviceî. Refer to error code 535. 550 this contact form persists. 360 Dispenser invalid return ID.

Triton Error 563

Reset the as needed.

If the error clears, put Inspect cables connecting the Printer Controller Module to the Printer to verify that the main board and on the electronic journal. 2. Baud rate set to the command that caused the error code. Remove jammed may be dirty.

Check data and power panels are closed and secured. Place all belts on on the dispenser main board. cables for damage. Retry the test operation and request fifty completing several Test Dispenses.

9100, 9600, 9700, 9800, Mako, RL1600, RL2000, RL5000, RT2000146No reply from command to electronic journal1. If the problem persists, replace the dispensing mechanism.8100, 9100, 9600, 9700, 9800, Loading... Make sure that note qualifier and printer locking screw. Remove any DC power if either is defective. 3.